Land Rover Parts  – Series 3

Front Drive Shaft 4 Cly models

Set of 4 New Brake Shoes 10inch suits most SWB front and rear

Replacement Brake Adjuster Snail Cam for 11\" front brakes. RH and LH available, priced per each

Crank Handle 4 Cylinder

Muffler and Tailpipe

Head Lamp Bezel

Military Spark Plug RSN8

Replacement carburettor for 36IV Zenith

Cage Nut for door hinge screws

Bonnet Lock Kit

Fuel Filler Hose to suit S2 and 3 Vehicle with Fuel tank under drivers seat,LH tank hose also available for Skippy models

Fuel Filler Hose to suit S2a and 3 Vehicle with Fuel tank in rear

Front Brake Shoes to suit 4 cyl LWB

Transmisson Hand Brake Shoes Series 2&3 4 Cly

Speedo Cable to suit Series 3 4cyl

Rear Main Oilseal Kit 4 Cly 3 main bearing model, 5 main bearing model also available

Fuel Cap to suit Series 2,3,early Defender,please check for correct type

Ring Gear 4 cly petrol

transfer case trust washer 4 Cyl

Door Seal Rubber sold per metre

Axle Castle Nut

Split Pin Shock Absorber

Screw Brake Drum retaining

Deluxe Seat Base Outer

Deluxe Seat Back Outer

Carb rebuild Kit to suit Zenith 36IV

Hand Brake Boot to suit S2a and S3

Folding Side Step Kit

Transfer Case Boot to suit S2a and S3

Swivel Pin Kits or sperate parts available.Please Enquire for your specific model

Heater Tap and Hoses,Please Enquire for your specific needs

Engine or Gearbox Mount

U Bolts and Nuts,Please Enquire for your specific model

Suspension Bushes and Bolts,Please Enquire for your specific model

Thermostat and gasket for 4 Cly or V8 Please Enquire for your specific model

4.7 ratio (47-10) Rover diff crown wheel and pinion

Clutch master and slave cylinder to suit Series 3 and Defender,Please Enquire for your specific model

Bolt for outrigger under firewall

Top hose $18-00,Bottom Hose $18-00, By pass $7-31

Pedal pad rubber

Engine dipstick for Series 2 and 3 2.25 petrol or a prize for that special person

Inner guard and nose panel RH and LH available

Distributor Cap and Rotor to suit Army V8 with non lucas system.Please Enquire for your specific model

Oil Pump Gear Set

Exhaust downpipes for 109 V8,we also carry Y section and mufflers for this Model.Please Enquire for your specific model

Plastic Grille for S3

Mesh gille for Series 3 109 V8

Lucas 3 position Head Lamp Switch

Diesel Ignition/Glow Switch

Fuel Pump Rebuild Kit for Series 2 and 3 4 cylinder petrol and diesel

Tailgate with Hinges Brand new but may have some scratches (3 only at this price)

Rubber Buffer for seat back $2.00 set of 4

Tie rod end, RH or LH thread available

Axle Oil leaks please ask for your requirements

Universal Joint kits for drive shafts and series front axles.please ask for your requirements

Oil Pump Assembly

Door Top Kit for Series 2 & 3 Our Kit includes: A bare door top. Window track 10 Stainless screws to fit track. Ready for you to fit the glass from your old door tops Please specify Right or Left side when ordering

These are deluxe style bonnets to fit all Series 2 & 3 models, except V8. They have the recess for carrying a spare wheel. This style is not readily available new elsewhere and current retail price in UK is over ?300. They are new but have some shop wear - mainly scratching and scuffing from handling, no dents.

Dash top for Series 3, approx 1976 on.

These latches are for all Series 3 vehicles fitted with the "antiburst" style locks. Available for both front doors and rear end door (please specify when ordering). If you wish to replace the standard "slam" type latches these are also stocked. Can also supply the door strickers to convert from slam to antiburst - please enquire.

Replacement Rear Cross member. When the rear cross member of a chassis is has rusted or been damaged complete replacement is a cost effective alternative to rebuilding. Can be easily welded into the chassis saving many hours of cutting and fabricating. NOTE: This one has extention as shown in the photo. Also available without extentions (price is $407)

We stock a range of repair pieces for repairing rusty chassis and bulkheads. These pieces are made to the pattern of the original and are simply welded in to replace a rusty or damaged section. Please enquire as to the price and availability of the specific section required

This CD contains a range of original LR parts books, workshop manuals and owners handbooks. Disc is genuine copyrighted Land Rover product and cannot be returned once packaging unsealed Minimum system requirement: Pentium 3, 128MB RAM OS Windows 2000 & XP (Does not work in Vista)

These are deluxe style bonnets to fit all Series 2 & 3 models, except V8. They are new but have some shop wear - mainly scratching and scuffing from handling, no dents.

To repair rusty floors in Series vehicles these footwell repair pieces can be welded in. A very cost effective and convenient alternative to fabricating from scratch. Usually sold in pairs but occasionally individual sides are available.

When the rear end door gets a bit saggy it can be easily fixed by fitting these hinge pin kits. They consist of the pin, brass ball and spring.

Gear Lever Knob for Series 3 - push on fixing